Utax CLP 3416 Especificaciones Pagina 57
- Pagina / 148
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Using the Operator Panel
ADVANCED OPERATION GUIDE 2-29
Changing the Interface Parameters
The printer is equipped with both parallel and USB interfaces. Optional
serial interface board kit and network interface card can also be installed.
Various printing environment parameters such as the default emulation
can be changed independently on different interfaces by using the printer’s
menu selection system. Select the interface to apply the changes in the
procedure described below.
NOTE: This interface selection described below does not select the
interface from which data will be received. The printer automatically
selects the interface.
Changing Parallel Interface Mode
The parallel interface supports a bi-directional/high-speed mode according
to IEEE standards. Normally, this interface is used under the default setting
Auto. For details, see Parallel Interface on page 4-3. After setting the
interface, be sure to reset the printer or turn the power off at least once.
The new setting will be enabled thereafter. You can select from the
following:
• Auto (default)
• Nibble/high speed
• High speed
•Normal
1
Press [MENU].
2
Press U or V repeatedly until Interface > appears.
3
If the interface is other than parallel, press
[ENTER]. A blinking question mark (?)
appears.
4
Press U or V repeatedly until Parallel
appears.
5
Press [ENTER] again. The question mark disappears.
6
To change the parallel interface mode, press Z. The current
communication mode appears.
7
To change the communication mode, press
[ENTER]. A blinking question mark (?)
appears.
Interface
? Serial
Interface
? Parallel
>Parallel I/F
? Nibble (high)
- Colour printer 1
- CLP 3416 1
- Contents 3
- Introduction 5
- Guides Included 6
- Conventions 7
- 1 Handling Paper 9
- General Guidelines 10
- Recommended Paper 11
- Selecting the Right Paper 12
- Smoothness 13
- Basis weight 13
- Thickness 14
- Moisture Content 14
- Paper Grain 14
- Other Paper Properties 15
- Special Paper 15
- Top sheet (white 16
- Adhesive 16
- Carrier sheet 16
- Top sheet 17
- UnacceptableAcceptable 17
- NOTE: If the paper jams even 18
- Paper Type 20
- Loading Paper 21
- Setting the Cassette Paper 22
- Size on page 2-63 22
- Release Lever 23
- Paper Guides 23
- Paper Stopper 23
- Load Limit Load Limit 24
- Clip Clip 25
- Paper Gauge 25
- Paper GuidePaper Guide 27
- Load LimitLoad Limit 27
- Incorrect 28
- 2 Using the Operator Panel 29
- Message Display 31
- Indicators in Message Display 33
- †. Only with MP tray feeding 34
- ATTENTION 35
- Canceling a Printing Job 38
- Menu Selection System 39
- >Type Adjust > 40
- >>Paper Weight 40
- Normal 1 40
- Menu System Road Map 41
- MENU MAP 42
- Status Pages 43
- 1 Firmware Version 44
- 2 Hardware Information 44
- Using Quick Copy 47
- Using Proof-and-Hold 48
- Changing e-MPS Configuration 53
- Interface 58
- ? Parallel 58
- ? Serial 58
- ? Network 60
- Interface > 60
- Resolving IP Address 61
- Using the Operator Panel 64
- 2-36 ADVANCED OPERATION GUIDE 64
- Making Default Settings 65
- Default Font 66
- ADVANCED OPERATION GUIDE 2-43 71
- Samples of Fonts List 71
- Pagination 72
- Page Protect Mode 73
- Linefeed (LF) Action 74
- Carriage-Return (CR) Action 75
- Wide A4 Pitch 75
- >Wide A4 76
- Setting Print Quality 77
- Gloss Mode 78
- Operating the Storage Device 79
- Memory Card > 81
- >Write Data 81
- >Write Data ? 81
- >List of 84
- Partitions 84
- Using the Optional Hard Disk 85
- Using the RAM Disk 86
- Paper Handling 88
- Setting MP Tray Paper Size 89
- Paper Handling > 90
- >MP Tray Type 90
- >Cassette Size > 91
- Custom 91
- >Cassette Size 91
- ? Custom 91
- >>Unit 92
- Duplex Printing 95
- >Duplex Mode 96
- >Override A4/LT 97
- Creating Custom Paper Type 98
- Selecting the Output Stack 100
- >Stack Select 101
- Top tray FaceDn 101
- ?Top tray FaceDn 101
- Color Mode 102
- Reading Life Counters 103
- >New Toner [C] 104
- Installed ? 104
- Other Modes 105
- Setting the Sleep Timer 106
- Received Data Dump 108
- Printer Resetting 109
- Resource Protection 110
- Alarm (Buzzer) Setting 110
- Auto Error Clear Setting 111
- Setting the Error Clear Time 112
- Color Registration 114
- >>Adjust Cyan 115
- L= H= R= 115
- H= 00 R= 0 115
- Color Calibration 117
- 3 Options 119
- General Information 120
- Expansion Memory Modules 121
- Installing the Memory Modules 122
- Memory Card 124
- PF-60 Paper Feeder 124
- DU-300/DU-301 Duplex Unit 125
- PT-300 Face-up Output Tray 126
- Hard Disk 127
- Option Interface 128
- 4 Computer Interface 129
- Parallel Interface 131
- USB Interface 133
- Serial Interface (Option) 134
- RS-232C Protocol 135
- PRESCRIBE FRPO D0 Command 137
- RS-232C Cable Connection 138
- Glossary 141
- ADVANCED OPERATION GUIDE 1 143
- 2 ADVANCED OPERATION GUIDE 144
- ADVANCED OPERATION GUIDE 3 145
- 4 ADVANCED OPERATION GUIDE 146
Relacionado con productos y manuales para Las Impresoras Láser / Led Utax CLP 3416
(111 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.031 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales